The appearance of furniture can become unpresentable over time. In addition, it sometimes breaks down and requires repair. Restore a chair that can still serve long years is not difficult at all. Sometimes you just need to refresh the surface - change the upholstery or make the seat more durable. For restoration, many materials are in the house - a piece of dense fabric, foam rubber, etc. The updated chair, covered with a beautiful varnish, looks no less neat than when purchased.
The appearance of furniture can become unpresentable over time.
A chair that is refurbished at home can be decorated better than it looked before. The restoration requires a minimum of materials and tools. Changing a leaky or worn upholstery is a matter of one hour.
If the chair is antique, then you need to restore it very carefully.
You can clean it yourself wooden surface old furniture and cover with a transparent or tinted composition, add new elements to the decor. For example, a chair is made with carved legs or a back, reinforcing the seat so that long time use it for its intended purpose.
For restoration, many materials are in the house - a piece of dense fabric, foam rubber, etc.
The cost of home restoration is minimal. Before buying a new chair, think about whether you can restore the old one and save a lot at the same time. Restoration of antique furniture is especially expensive as it requires great care and exclusive materials. Updating furniture on your own will cost much less.
The updated chair, covered with a beautiful varnish, looks no less neat than when purchased.
Restoration process: step by step instructions
If the "native" bolts connecting the supporting structure are loosened, then they are strengthened with an additional washer. For greater security, you can add some all-purpose glue to the grooves.
Replace old seagrass and horsehair fillers with foam rubber.
A leaky seat is refurbished by replacing the lamella base and / or completely refurbishing the upholstery. The worn-out surface is freed from old material. The chair is being prepared for further restoration:
- cut a piece of plywood to fit the seat;
- foam rubber is glued onto the base (width - 3-4 cm);
- fix the plywood around the perimeter;
- pull the upholstery fabric onto the finished base;
- fix the material with a stapler and staples.
A chair that is refurbished at home can be decorated better than it looked before.
You can completely replace the back with a curly one, if the design allows.
You do not have to run the fabric on the outside of the seat. Then the upholstery is tucked inward around the perimeter. The seat frame will then be visible.
The fabric is selected to be resistant to abrasion and mechanical stress, sufficiently dense.
Changing a leaky or worn upholstery is a matter of one hour.
When updating, you can use the most different materials... With good carpentry skills, the restored chair takes on a personal touch. This takes into account the material - wood species, density, texture.
You can independently clean the wooden surface of old furniture and cover it with a transparent or tinted composition, add new elements to the decor.
The chairs included in the kit must be decorated in the same style.
If the chair is antique, then you need to restore it very carefully. Be sure to give time to dry the applied composition.
For an antique chair, choose decorative material with embroidery.
For your information... Antique chairs often come with springs in the seat area, so you will need to find the same or similar, and remove old, rusted and lost elasticity. Replace old seagrass and horsehair fillers with foam rubber.
The cost of home restoration is minimal.
Round off the edges using a jigsaw and sand the edges with sandpaper.
Required materials and tools
To restore the chairs, you will need the following:
- quick-drying varnish (transparent or tinted);
- dye;
- upholstery fabric;
- foam rubber;
- plywood;
- sandpaper;
- metal washers and bolts (screws);
- springs (for a specific type of chair).
Sandpaper is required in order to clean the surface of the furniture from irregularities, chips and cracks in the varnish.
The fabric is selected to be resistant to abrasion and mechanical stress, sufficiently dense. Tapestry, flock, matting, etc. will do. For an antique chair, choose a decorative material with embroidery.
Updating furniture on your own will be much cheaper.
Select a wooden base according to density and texture in advance, cut it to size and use a template to draw up the desired pattern.
Emery paper is required in order to clean the surface of the furniture from irregularities, chips and cracks in the varnish. The chair must be completely sanded ( wooden structure) for smooth application of the laminating compound.
For major repairs, the chair can be disassembled, the broken off parts can be replaced with new ones and fastened with bolts or screws.
To upgrade a chair, you need tools:
- scissors;
- roulette;
- a hacksaw for wood (cut off the excess plywood under the seat);
- screwdriver;
- screwdriver.
For greater security, you can add some all-purpose glue to the grooves.
For major repairs, the chair can be disassembled, the broken off parts can be replaced with new ones and fastened with bolts or screws. Seat frames also often require restoration.
Seat frames also often require restoration.
A Viennese chair or whatever looks best in this design.
Important! It is necessary to use wood species that are close in density and texture to make the chair functional and presentable.
The leaky seat is renewed by replacing the base with sipes and / or completely restoring the upholstery.
Restoration methods by decorating the chair
There are several options for decorating the appearance of furniture. The chair can be refurbished in the following ways:
- staining;
- lamination;
- decoupage.
It is necessary to use wood species that are close in density and texture to make the chair functional and presentable.
As a decor, you can use both the upholstery itself, picking up fabric of interesting colors like a tapestry, and the rest of the furniture, making them carved, curly.
You do not have to run the fabric on the outside of the seat.
The plain seat is decorated with smooth embroidery or appliqué. This must be done before starting the sheathing.
The plain seat is decorated with smooth embroidery or appliqué.
The wooden surface of the support structure and the back are laminated, that is, they are coated with a resistant varnish in several layers. The tone of the coating is selected closer to the natural shade of the wood (light, dark or moderate). A Viennese chair or whatever looks best in this design.
The restored chair can be additionally decorated - to make the wooden surface lighter or darker, to arrange the back or legs in a different way.
You can completely replace the back with a curly one, if the design allows. Select in advance a wooden base according to density, texture, cut it to size and use a template to draw up the desired pattern. Round off the edges using a jigsaw and sand the edges with sandpaper.
The wooden surface of the support structure and the back are laminated, that is, they are coated with a resistant varnish in several layers.
The chairs included in the kit must be decorated in the same style so that they do not stand out from the overall picture - "different-sized" furniture can look good in different rooms, but at a common table, for example, when celebrating a family celebration, it looks casual.
A wide variety of materials can be used when upgrading.
VIDEO: Chair restoration: How to make a chair with your own hands. Master class from Katerina Sanina: design, interior
Sometimes it doesn't make sense to buy new chairs at an overpriced price. Often, exquisite designer furniture is created from old, completely restored blanks. Do-it-yourself chair restoration will help "breathe" a second life into the decoration of the apartment with the help of the following instructions and advice from experienced craftsmen. Ultimately, you will end up with a durable and comfortable product knowing how to get it repaired. The updated Soviet chair will become a real property of the home interior.
Even high-quality furniture elements are susceptible to mechanical damage and surface abrasion. Often ours is our fault. home furniture become unusable. The legs and back suffer the most - other parts are more or less intact. From old chairs, first-class poufs and an armchair are often twisted and decorated with their own hands. It costs a lot of money when ordering a service from a professional designer to refurbish a chair.
At home, you can carry out restoration without the help of a professional carpenter wooden chairs with a backrest and stools - it is not necessary to have a lot of experience with arts and crafts. It is enough to see at least once how you can make a constriction of the soft part. What you have seen will help you navigate how long the restoration of your chair will take.
The experience gained will help in the future to experiment with more complex structures (entrance hall, sofa, wardrobe, table, bed, chest of drawers and other wooden attributes of the house). A completely unnecessary and aged thing can be turned into a real functional decorative element. All this can be done from the old chair in a new way.
Craftsmen know different ways to restore furniture - alteration of a chair and restoration of a stool depend on the degree of damage to the parts. The most common chair breakages are:
- leg damage, loose back, loose seat, other flaws in wooden parts;
- deterioration of the upholstery of old furniture;
- severe abrasion of the paintwork.
The repair scheme should be selected depending on the presence of certain problem areas. In many cases, it is enough to fasten the parts with new fittings. The same renewal trend extends to worn upholstery. The worn-out fabric and foam rubber must be replaced with new elements: sheathed with a new flap. In fact, there are no antique chairs that are unusable for restoration, even if your grandmother painted them. In the master class below, you will learn how to update an old chair and how to tastefully paint its surface.
Overwhelmed Before and After Chairs
1
2
3
4
5
6
Refreshing the color and construction of old wood
The complete or partial transformation of the restored chair directly depends on the availability of certain tools and materials. Not many people know how to properly refurbish old home chairs. In the process of restoring kitchen furniture, you cannot do without a drill (screwdriver), a small hammer, two different types screwdrivers, scissors, paintbrushes, clamps, stapler with mounting brackets, sandpaper, small mallet and scissors. As the last component you will need:
- self-tapping screws;
- glue for wood;
- foam pillow;
- varnish-coloring agents;
- a piece of upholstery fabric.
At the first stage of the repair, the surface should be restored. Furniture is cleaned of dust, thoroughly wiped with a wet sponge. Next, the seat and back of the case are removed and the component parts are disassembled. Sometimes it needs to be fixed. Use a rubber mallet instead of a metal hammer to avoid damaging parts.
If the chair is assembled with screws, the structure is disassembled without special efforts do it yourself. It is enough to unscrew them for complete dismantling. You need to fold them in such a way that you do not confuse them later. To clean the remains of epoxy glue, use a moistened rag, then gently scrape off with an old blunt knife. The cleaned frame is left to dry for a while. Only then the structure is restored and altered.
To remove epoxy adhesive in labor-intensive areas, instead of water, use the pressure of a jet of steam. In the absence of a special device for performing a delicate procedure, the proven "old-fashioned" method is used - the use of a hose with a tip, which is put on the spout of the teapot to transform the tree.
Changing the look of furniture: the best example
The step-by-step process of restoring an old chair should be carried out as follows:
- Processing with putty from all kinds of chips and cracks.
- Grinding wood with different types of sandpaper (first with a coarse-grained sheet, then with a fine-grained sheet).
- Inspection of the complete structure to be repaired (fixing wobbling by gluing and other methods).
- Seat restoration (upholstered or hard seat).
- Decorating the surface of the base of a wooden chair (varnishing or painting).
Removing the old varnish The sanding machine will speed up the process of removing the old layer. You can securely fix the legs with the help of wooden kerchiefs. Studs with nuts and washers will also be needed.Polishing and painting is best done on fresh air
We stretch the upholstery, fixing it with a construction stapler at a distance of no more than 1-2 centimeters. Depending on the shape, the fabric at the corners can be fixed like this Another way of fixing the fabric at the corners
How to remodel and paint an old wooden chair
Do-it-yourself restoration of old chairs is aimed not only at updating the frame. The upholstery of an antique chair can be decorated different ways with your own hands:
- Fabric padding of the soft part or removable top cover.
- Updating the back with a decoupage pattern for antique chairs.
- Restoration of the back with durable textiles (denim, jgut, tapestry, jacquard or velor).
- An additional decoration for the upholstery is macrame.
- Padding of too soft backrest with belts (you need to remove the old upholstery, change it to a simple mesh with square cells).
On the net you can find a huge number of photos and videos of different ideas of masters who restore furniture. The new backrest of the old furniture attribute can be decorated with a self-sewn fabric cover. Individual capes and covers can be changed based on the changeable design of other attributes of the house. Each master decides for himself what can be done using old wooden chairs. Choosing what to paint, you will restore the product in an individual style.
It is very disappointing to throw out the thing that is included in the furniture set in the trash. Do-it-yourself restoration of chairs will help not to violate the complete set. Also, do not be upset if something fails that plays the role of an exclusive, dear to heart, memorable item. And here the restoration is capable of performing real miracles.
Chairs paintwork
What is a favorite chair? These are wonderful moments of returning to childhood ... Or the memory of close person... Or even a chair can be passed down from generation to generation. Or something else, but so dear, with which you just don't want to part.
But, unfortunately, a thing cannot last forever. Scratches appear on the furniture and peels off. alas, it becomes unpresentable. However, restoring old chairs with your own hands will help preserve the item for a while.
Often, before varnishing, the chair needs to be completely cleaned of old paint or varnish. This process requires patience and perseverance from the master. But the payment for labor will be consistent with the effort invested.
Decorating chairs
Sometimes it makes sense to drastically change color solution furniture. Chairs painted in white or gold look very creative. Often, craftsmen choose other colors for the wooden part of the chair: blue or light blue, pink or bright red. But then the upholstery should be pure white or with a golden ornament. The elegance of this design is carried over to the times of Catherine II, reviving palace luxury.
White furniture can be decorated with gilded ornaments, simply drawn or made in the form of a bas-relief. Blanks for this kind of jewelry can be purchased in stores or cast from plaster yourself and glued. Do-it-yourself restoration and decoration of chairs in antique style will add charm and originality to the design. Sometimes the edges of the upholstery are decorated with beautiful braid, tassels.
Chairs painted in a cubic style will also change the image of the room. And someone more will like floral or plant colors. In any case, the surface coating will protect the object from corrosion and increase its service life. Therefore, the practical benefits that such a restoration of chairs with your own hands will bring is also obvious.
Comprehensive instructions for replacing defective parts
In addition to the appearance of the products, the owners of beautiful antique chairs are worried about their functionality. Therefore, the restoration of wooden chairs with your own hands includes the replacement of some parts in the product. For example, it is difficult to grind a broken rail from the back of a chair exactly identical to the rest. Therefore, it is recommended to make the number of strips of a different configuration, but of the appropriate size (height and thickness). You can even try to get them from the store, although this will be very difficult.
Renovation of Viennese chairs
Very often the slats simply fall out of their nests. Usually Viennese chairs suffer from this defect. Do-it-yourself restoration in this case occurs according to the above algorithm. Only here it is no longer necessary to remove all the slats from the lower grooves. It is enough to clean the vacant hollow from the remnants of dried glue, fill it with an adhesive compound and strengthen the dropped part in it.
Repair of an upholstered chair
Furniture plays an important role in our life. For example, soft chairs look elegant and stylish in the interior. And sitting on them is much more comfortable than on ordinary ones.
The most common repair is do-it-yourself restoration of chairs when it comes to upholstery that has lost its visual appeal. It also often has spots that cannot be removed by anything or even holes, ugly scuffs, and once bright colors fade. And sometimes you just want to change the entire design of the room, redo it in a different color scheme.
Do-it-yourself restoration of an upholstered chair will not take very long. Even an inexperienced master, teenager or woman can produce it. It is only important to choose a sufficiently durable upholstery fabric and professional furniture foam rubber.
Calculation of fabric when replacing upholstery
Often a set of furniture is used in the interior. In this case, the upholstery is usually replaced on all chairs at once. Therefore, the size of the tissue required for the restoration should be calculated in advance.
First you need to measure the width and length of the seat. Do not forget to add one centimeter on all sides for the hem of the fabric. Most often, this part is square, 50 by 50 centimeters in size, that is, 50 square centimeters.
Then, if the chair has a soft back, the same must be done with this part of the object. By calculating the size of the upholstery needed to restore one chair, you can calculate the amount necessary material for all chairs. Simply by multiplying the result obtained by the number of items (usually 6 pieces), the restorer will receive the number of square centimeters. They need to be divided by the width of the upholstery fabric, which is looked after in the store. The answer to this problem will be the number of required "running" centimeters.
It is best to buy a little more material, with a margin, since otherwise, the master may have to sew the fabric, because a piece will remain in one strip during cutting, and in the other - also a piece.
And in order to avoid this, the master will still need the ability to lay out patterns in this way on the fabric so that as little unused fabric as possible remains. It will not be difficult to do this if you need to prepare a number of details from the newspaper in advance.
Replacement of upholstery
If the restoration of old chairs with your own hands consists only in the fact that the master needs to change the fabric on the soft part of the object, then this will take very little time.
It is enough just to unscrew all the parts that require repair, that is, the seats and backs. Then the old upholstery is removed from them, a new one is applied, a hem is made, the edges are nailed with small furniture nails with wide hats. In the absence of such, small pieces should be cut out of cardboard or leatherette. Before hammering, you need to put them on nails so that they tightly hold the fabric, and do not slip through holes punched in the fabric.
First, the front of the seat is secured. Nails are distributed quite often, every 0.7 centimeters from each other. If necessary, small folds are made, which are permanently fixed.
Then the second symmetrical side is pierced, pulling on the fabric. After that, they work with the sides, leaving the corners free. Before hammering, stretch them thoroughly, straightening the fabric so that there are no folds on the front of the upholstery.
The last step in this repair is to fix the corners of the upholstery with staples. If the thickness of plywood or fiberboard used for the frame of the upholstered part of the chair is 3-4 mm, 4 mm brackets will be required. Be sure to take this fact into account! Naturally, if the frame is made of a material 10 millimeters thick, then the staples are taken ten millimeters.
Replacement of padding material when renovating an upholstered chair
The calculation of the amount of foam rubber is made in the same way as for upholstery fabric. Only now it is no longer necessary to add hem allowances. You can use batting instead of foam rubber.
Sometimes it makes sense to replace incomplete packing. Then it is enough just to put a "patch" in the place of pressing, cover everything on top with a thin layer of batting or foam rubber.
If it is produced complete replacement stuffing, then all parts should be removed from the seat: screws, staples, nails. It may be easier to cut a new piece of the seat from plywood or fiberboard, reinforce the padding on it, and cover it with new upholstery on top.
Bonding the joints of chair parts
Loose furniture can be repaired in two ways. One is to tighten the joints with screws or bolts. They should not be screwed into the old grooves, but next to them, if possible. Sometimes the craftsman needs to use or "patch" cut out of soft metal.
The second method is gluing. Then the chair is disassembled into parts, the joints are cleaned from the old glue. Having carefully missed the joints, the parts are connected and tightened with clamps.
Repairing broken legs
It is most difficult if the "injury" of the chair consists in a "fracture" of the part. Have regular chair you can completely replace the part by turning another. But it is almost impossible to make a twisted or curved leg at home, which, for example, Viennese chairs differ.
Do-it-yourself restoration in this case is done only with glue. Moreover, the contraction of the part must be done not only at the gluing points, but also at the ends of the leg, so that its size remains the same.
After drying, the joint is treated with sandpaper. For a more reliable fixation of the "fracture", it is necessary to grind with inside groove, into which you then glue the wooden plate, drowning it completely.
You can also use metal part by placing it on self-tapping screws. The place of the excavation is then carefully covered with putty or a mixture with sawdust, leveled, sanded and processed
Sometimes it can be difficult to part with your favorite things., among which there are sometimes pieces of furniture that were very useful, but outdated, and they are usually replaced.
But even if you bought a new piece of furniture to replace the old one, you can make something different from the last one, but no less useful.
Old chairs can be found in almost every home, and if you want to replace them, you shouldn't throw them away, as you can make other useful things for your home, garden and summer cottage out of old chairs.
For example, an old chair can be used to make a towel rack, a garden bench, a handy pet feeder, and more.
Here are some of the most interesting crafts you can make using old chairs:
Do-it-yourself alteration of an old chair: street bench.
For such a bench, you will need two or three chairs. These chairs can be spray painted or they can be kept looking old.
1.1. If the chairs are too high, you can file down their legs a little.
1.2. Special chair cushions are available. Some are sold separately (in which case they should be connected with a stitch), but you can find 4 pads connected together and cut off the excess part.
1.3. To make three chairs more like one bench, you can purchase or find two or three boards that need to be cut to the required length (the length of three chairs) and connected.
* You can round the ends if you like.
1.4. Prepare a piece of fabric that is longer and wider than the length and width of the cushions. Lay the fabric pattern side down on the floor and place the pads on it.
1.5. Lay the connected boards on top of the pads.
1.6. Bend the fabric and use a stapler to staple it to the boards.
1.7. All that remains is to put the boards and cushions on the chairs and add a few simple pillows to decorate.
New life for old wooden chairs: large dog feeders.
It will be easier for taller dogs if the feeders are slightly higher, especially for older dogs who find it difficult to constantly lower their head.
All you need is a file, a bowl and a pencil.
2.1. Before you start cutting a hole in your chair, you need to sandpaper it first.
2.2. Place the bowl upside down on a chair and trace with a pencil. After that, inside the resulting circle, draw a circle with a smaller diameter. This can be done with a pair of compasses or a plate with a smaller diameter than the bowl.
2.3. Make a hole inside the circle with a drill, from which you can then start cutting the circle. You can first cut out a smaller circle and test the stability of the bowl in the formed circle. Make the circle even larger if necessary.
2.4. Sand the inside of the hole with sandpaper.
* You can paint the chair and then insert the bowl.
Wall organizer from an old chair with a backrest.
By dividing the chair into parts, you can create a wall hanger or organizer, as well as a comfortable stool.
The back and seat will not be easy to separate, but then everything will be easy.
Sand all parts and paint if necessary.
To make a comfortable stool, you will need:
- tools for separating parts of the chair
- sitting from a chair
- durable fabric and pillow fill or regular small pillow
- stapler
- hot glue (if necessary) to hold the filled fabric.
1. Attach the fabric to the seat with a stapler, but leave one side untouched to fill the resulting pocket with pillow filler.
* You can also use a small pillow instead of filler.
2. Attach the seat back to the chair for a beautiful stool.
3. You will need hooks for the wall organizer. Once you've screwed on or glued on (self-adhesive) hooks, the organizer can be hung on the wall in the hallway, room or bathroom (on the door, for example), where you can hang towels on the hooks.
Converting an old chair into a menu board
You can make a beautiful menu board out of an old folding chair.
To do this, you will need:
- MDF sheets
- tools for separating the seat
- blackboard paint
- sandpaper (if necessary)
- paint or spray paint (if necessary).
1. From MDF, cut out squares of the required size for each chair (if there is one chair, then there is one square from MDF, respectively).
2. Paint the MDF square with chalkboard paint.
3. Remove the seat from the chair and bolt on the painted MDF square instead.
* In this example, for beauty, 2 old wooden parts were attached to the board, which fit the style of the board.
4. You can attach a chain between the legs to keep the legs in good shape.
How to convert a chair into a coat hanger
You just need to detach the back of the old chair, sand it and paint it.
After that, attach the hook of the required size and hang the hanger in any convenient place.
Bathroom hanger from an old chair
You will need a chair back. It can be carefully cut down, sanded and painted if desired.
The seat can be cut in half and one half can be used as a hanger shelf.
This shelf can be attached with bolts and special glue. You can use corners to reinforce the shelf in place. This step is optional, it is suitable for those who like working with wood.
This hanger can be attached to the door in the bathroom, in the kitchen, in the country or in any other room where it may be needed.
How to convert old chairs into shoe storage
Separate the seat from the chair. If this is not possible, then you will have to cut a large hole into which you will then need to insert the basket.
Find any basket (metal or plastic) and use strong thread or wire to attach it to the chair (tied to the chair frames).
What to make out of an old chair: swing
If you cut the legs of an old chair, sand it and paint it, then it can be used as a swing seat in the country or in the garden, for example.
You will need:
- strong rope
- metal rings
- screws with an eyelet
- additional details if necessary.
Here's another swing option:
The second life of a chair: garden shelf
An old chair can be turned into a handy shelf for flowers or storage of various garden tools.
You will need a chair back and some (or all) of the seat. Simply detach the desired part of the seat (you may need to saw off the chair legs) and attach the shelf to the wall or door.
Sand the part and paint.
Diy shelf for drinks from an old chair
1. Find a bucket containing ice and drinks. It is desirable that it be with handles that would rest on the frame of the chair.
2. Separate the seat from the chair, cut it down or make a hole in the seat.
* A strong rope can be used to tie a bucket or large bowl to a chair if there are no handles. It is most convenient to make holes in the bucket through which the thread is threaded.
The second life of an old chair: a flower bed
For the garden, you can create beautiful flower bed using an old chair.
To do this, you will need:
- flower pot
- jigsaw
- sandpaper (for wood processing)
- paint (if desired)
- paste-sealant to smooth out irregularities in the hole in the chair (if necessary).
* If you want to attach a few more flower pots to the chair, you can use a pipe clamp to hold the pots or jars.
Diy photo of flower beds from old chairs
DIY clothes hanger
If you carefully cut down the upper part of the back of an old chair and sand it with sandpaper, you can create an original clothes hanger.
If you have the opportunity to create several of these hangers, then you can paint them in different colors to make your wardrobe look beautiful.
* The entire back of the chair can be used.
Old Chairs Decor: Photo Frame
You can wrap the back of an old chair with a strong thread and use clothespins to attach photos to this thread.
If the thread slips, then it can be fixed with tape or hot glue, or you can make small cuts in the places where the thread touches it on the back of the chair.
If you wish, you can put a small flower on the chair for beauty.
New life for an old chair: bathroom shelf
If the old chair is sanded and painted, then it can be used as a shelf and towel rack in the bathroom or in the country.
Just flip the chair over and bolt it to the wall or door.
* You can file the chair legs if necessary.
Sooner or later, even the sturdiest chairs fail. It is a pity to throw them away, because they have already become part of the interior, they have fallen in love and keep in themselves a lot of spiritual memories. If this is the case, then it is worth thinking about the practical rework of old furniture and its conversion into new interior items. What can come out of the most ordinary old chairs?
In the interior of a summer house or house, decorated in rustic style items with history look special. They give the space a special retro-gloss and create a real touch of antiquity, which is so necessary in interiors of such a plan. This is where towel racks made from the backs of old chairs will be appropriate. It will not be difficult to create them, but they will colorfully fit into the design picture. You can safely decorate kitchens or bathrooms with such decor items.
Are the legs loose or broken on the chair? No problem! This does not mean that his life is over. If the case itself is strong enough and has an attractive appearance, then its best purpose is to become a garden swing. Previously, it is worth sanding the piece of furniture, soaking it with an antifungal solution and painting it in a beautiful color. At the same time, the paint must be resistant to temperature extremes, precipitation and strong sun.
In the same garden, it is appropriate to put an unusual planter, also made from an old chair. Sometimes it happens that after renovation, all furniture is completely changed, but there is no desire to get rid of the old one. In this case, the garden and even the interior of the house can be decorated with stylish flower stands. One has only to freshen the chairs with paint, cut holes in the seats and place large pots of flowers there (these can even be small tin containers).
Today it is fashionable to decorate the kitchen with items that are found in popular cafes or restaurants. These also include slate tablets, on which menus are usually written or pleasant wishes for visitors. The most interesting thing is that it is not at all difficult to make such a decor item, and it will not require special costs. All you need is the back of an old chair and slate paint. By the way, young parents should also take this idea, because children love to draw with crayons so much.
It's amazing how many varied and interesting home furnishings can be obtained using only old chairs. Moreover, such old furniture with new life able to stylishly diversify the interior. Here, for example, a coffee table made from a chair, which is also perfect for the role of a bedside table.
Shelves are never superfluous, wherever they are - in the bathroom, in the living room, in the kitchen, in the hallway or even in the garden. Creative hanging shelf will come out of the upper part of an old chair and will always delight you not only with its functionality, but also with its attractive design.
We have also compiled a selection. It's worth taking a look at!
